Liquid Nails Subfloor and Construction Adhesive

1.Eliminates Squeaky Floors 2.Easy cold weather gunning formula 3.Bonds wet,frozen and treated lumber 4.Interior and Exterior

PRODUCT DESCRIPTION

BY-SF Subfloor & Deck Construction Adhesive is a specially formulated weatherproof-grade adhesive for interior and exterior construction, offering easy cold weather gunning ability. Penetrates wet, frozen and treated lumber, Ideal for bonding common building materials to concrete.

RECOMMEND FOR increasing the structural integrity of wall, deck and subfloor systems using the following common building materials:

Lumber and treated lumberPlywoodWaferboardEngineered lumberParticleboardOSB

NOT RECOMMENDED FOR uses other than subfloor, deck and wall system

installation, or underlayment directly to concrete without proper vapor barrier and

fasteners.

Please research all installation instructions and read entire label for safety, health

& environmental information prior to use.

PRODUCT ADVANTAGES

1.  Eliminates Squeaky Floors

2.  Easy cold weather gunning formula

3.  Bonds wet, frozen and treated lumber

4.  Bonds composite materials

5.  Interior & Exterior

6.  Tough, durable and flexible

TECHNICAL PROPERTIES

Base	Synthetic   rubber & resin
Type	Solvent   elastomeric adhesive
color	Light   Tan, Beige, White, transparent
Appearance	Smooth   paste
Weight   Per Gallon	10.9pounds(1.3kg/L)
Viscosity	220000CPS
Volatiles	34%
Solids	70%
Flammability	Extremely   flammable, nonflammable when dry
Flash   Point	1°F(-17°C)
Application   Temperature	-4°F   to 104°F(-20°C to 40°C)
Service   Temperature	-22°F   to 212°F(-30°C to 100°C)
Adhesion	Excellent   to most common building materials
consistency	Non-sag   under normal use
Bridging   Ability	Excellent   bridges gaps to 3/8’’(1cm)
Extrudability	Very   easy to gun at room temperature
Shear   Strength	24   hours – 220psi 48   hours – 320psi 28   days – exceeds 480psi
Durability	Very   good; estimated to exceed 40 years
Flexible	Excellent
Water   Resistance	Very   good
Exterior   Weathering	Very   good, not recommended for direct exposure to sunlight
Aging	Excellent   after accelerated aging cycle
Freeze   – Thaw- Stable	Does   not freeze
Bleed	None
Staining	None
Odor	Mild   toluene
Working   Time	Adhere   within 15 minutes
Drying   Time	Full   cure in two weeks
Paintability	Paintable   with oil and latex based paints
Coverage	30   lineal ft. using 1/4’’ bead for 10fl.oz
Shelf   Life	24   months from date of purchase
Specification	Exceeds   ASTM AFG-01 & ASTM-D-3498
MAX   VOC	388GPL

SURFACE PREPARATION

 

Make sure that all surfaces are clean, structurally sound and free of excess water. Wood

can be damp, but the adhesive will take longer to dry. BY-SF can be applied at

temperatures as low as 10°F (-12°C).

 

APPLYING THE PRODUCT

 

Condition BY-SF adhesive to at least 40°F (4°C) for easier gunning. Adhere

materials within 15 minutes of gunning adhesive. Make sure skin of bead is broken. If not,

scrape off bead and apply fresh bead.

 

Subfloors:

 

Conventional or tongue and groove: Lay one 1/4" (.64 cm) zigzag adhesive

bead on each joist. On supporting joists where sheets meet, lay two zigzag beads for

added strength and to prevent squeaking. Space joints the thickness of a putty knife to

allow for expansion. Nail section into place with 8d annular or spiral nails 12" (30 cm) on

center of all joists. Subfloor must be under roof within 6 weeks of construction. Proper

installation methods for subflooring must be followed.

 

Decks:

 

Use a 1/4" (.64 cm) bead on every joist for added strength and to prevent

squeaking. Nail planks at every other joist; pre-drill nail holes to prevent splitting of wood.

PACKAGE:

BY-SF is available in 10fl.oz (296ml), 28fl.oz(828ml) cartridges, also can customze 1000ml foil pack, 24pcs in a carton.

Liquid Nails Subfloor and Construction Adhesive